Unofficial File parts/65084.dat
Warning: Model breaking changes to unofficial parts may occur anytime prior to release
0 Duplo Plate 2 x 2 with Hinge Extended on Side and Red Gaskets
0 Name: 65084.dat
0 Author: Peter Blomberg [WUIt]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Licensed under CC BY 4.0 : see CAreadme.txt
0 !HELP Secondary hinge position at 0 -5 120
0 BFC CERTIFY CCW
0 !CATEGORY DuploShow file code:
1 16 0 0 0 1 0 0 0 2.75 0 0 0 1 stug7-2x2.dat
1 16 0 0 0 1 0 0 0 1 0 0 0 1 s\65084s01.dat
1 16 0 0 0 -1 0 0 0 1 0 0 0 1 s\65084s01.dat
1 16 0 0 0 1 0 0 0 1 0 0 0 1 s\65084s02.dat
0 // bottom reinforcements
1 16 0 4 -26 0 0 -1.5 0 4 0 10 0 0 box3u5p.dat
1 16 0 4 -16 0 0 1.5 0 4 0 1.5 0 0 boxjcyl4.dat
1 16 0 4 20 0 0 1.5 0 4 0 -4 0 0 box3u8p.dat
1 16 0 4 16 0 0 1.5 0 4 0 -1.5 0 0 boxjcyl4.dat
1 16 0 4 24 0 0 1.5 0 4 0 1.5 0 0 boxjcyl4.dat
0 // bottom helm
4 16 -40 24 -40 -36 24 -36 36 24 -36 40 24 -40
0 // large box inner surface
0 BFC INVERTNEXT
1 16 0 14 76 0 0 36 10 0 0 0 -112 0 box3u2p.dat
3 16 36 4 -36 -36 4 -36 0 4 -16
3 16 0 4 16 -18.5 4 71 18.5 4 71
0 // outer surfaces
1 16 0 12 -40 0 0 -40 -12 0 0 0 1 0 rect.dat
3 16 -16.5 0 74 0 0 14 16.5 0 74
3 16 -40 0 -40 40 0 -40 0 0 -14
0 // understud with snap ring
1 16 0 4 0 1 0 0 0 -4 0 0 0 1 stud8a.dat
1 16 0 4 0 16 0 0 0 -1 0 0 0 16 4-4edge.dat
1 16 0 4 0 16 0 0 0 -1 0 0 0 16 4-4ndis.dat
1 16 0 0 0 14 0 0 0 -1 0 0 0 14 4-4edge.dat
1 16 0 0 0 14 0 0 0 1 0 0 0 14 4-4ndis.dat
0 BFC INVERTNEXT
1 16 0 0 0 14 0 0 0 4 0 0 0 14 4-4cyli.dat
1 16 0 24 0 1 0 0 0 1 0 0 0 1 dsnapridge.dat
0 // fittings
2 24 40 24 80 40 24 123.2713
4 16 40 24 80 36 24 80 36 24 112.7287 40 24 123.2713
1 16 40 14 120 0 -1 0 3 0 0 0 0 -3 2-4ndis.dat
1 16 40 14 120 0 1 0 3 0 0 0 0 -3 2-4edge.dat
4 16 40 5.7479 109.2521 40 11 117 40 11 120 40 5.7479 130.7479
4 16 40 17 120 40 17 117 40 24 80 40 24 123.2713
4 16 40 24 80 40 17 117 40 14 117 40 5.7479 109.2521
3 16 40 5.7479 109.2521 40 14 117 40 11 117
2 24 -40 24 123.2713 -40 24 80
4 16 -36 24 112.7287 -36 24 80 -40 24 80 -40 24 123.2713
1 16 -40 14 120 0 1 0 3 0 0 0 0 -3 2-4ndis.dat
1 16 -40 14 120 0 -1 0 3 0 0 0 0 -3 2-4edge.dat
4 16 -40 11 120 -40 11 117 -40 5.7479 109.2521 -40 5.7479 130.7479
4 16 -40 24 80 -40 17 117 -40 17 120 -40 24 123.2713
4 16 -40 14 117 -40 17 117 -40 24 80 -40 5.7479 109.2521
3 16 -40 14 117 -40 5.7479 109.2521 -40 11 117Status
Needs 1 More Vote (CN)
Current Votes:
Takeshi Takahashi [RainbowDolphin]
This part has the following automated holds from the Parts Tracker
Part Dependencies
Official parents and subparts
Part Events
Peter Blomberg [WUIt]
initially submitted the part.
2025-07-18 22:30:41
Takeshi Takahashi [RainbowDolphin]
posted a vote of Certify
2025-07-22 13:19:25
Willy Tschager [Holly-Wood]
made the following comment.
2025-07-23 09:56:19
* Apparently 13355 and 65084 share geometry in common:
1 25 0 0 0 1 0 0 0 2.75 0 0 0 1 stug7-2x2.dat
4 25 -40 24 -40 -36 24 -36 36 24 -36 40 24 -40
3 25 36 4 -36 -36 4 -36 0 4 -16
3 25 0 4 16 -18.5 4 71 18.5 4 71
4 25 -40 24 -40 40 24 -40 40 0 -40 -40 0 -40
3 25 -16.5 0 74 0 0 14 16.5 0 74
3 25 -40 0 -40 40 0 -40 0 0 -14
1 25 0 4 0 1 0 0 0 -4 0 0 0 1 stud8a.dat
1 25 0 0 0 14 0 0 0 1 0 0 0 14 4-4ndis.dat
Question is why you didn't sub it as well?
1 25 0 0 0 1 0 0 0 2.75 0 0 0 1 stug7-2x2.dat
4 25 -40 24 -40 -36 24 -36 36 24 -36 40 24 -40
3 25 36 4 -36 -36 4 -36 0 4 -16
3 25 0 4 16 -18.5 4 71 18.5 4 71
4 25 -40 24 -40 40 24 -40 40 0 -40 -40 0 -40
3 25 -16.5 0 74 0 0 14 16.5 0 74
3 25 -40 0 -40 40 0 -40 0 0 -14
1 25 0 4 0 1 0 0 0 -4 0 0 0 1 stud8a.dat
1 25 0 0 0 14 0 0 0 1 0 0 0 14 4-4ndis.dat
Question is why you didn't sub it as well?
Peter Blomberg [WUIt]
made the following comment.
2025-07-24 07:59:53
These are common, but not part of the halves that were subbed. One would therefore need to make a separate subpart either for this common geometry alone or the whole that includes two references to the previously subbed half. Either works for me. However, I originally decided not to add another file to be reviewed separately. I wagered that copying 8 lines was less trouble.
Parts 13355, 65084, 65095, and 25548 shares a common snapping hole geometry that is larger than the snapping ridge (dsnapridge.dat). Here, I figured that it already would have been made into a primitive should such a subpart be desired. I chose not to create it. For what it's worth, I'd prefer having a primitive for the snapping whole.
Parts 13355, 65084, 65095, and 25548 shares a common snapping hole geometry that is larger than the snapping ridge (dsnapridge.dat). Here, I figured that it already would have been made into a primitive should such a subpart be desired. I chose not to create it. For what it's worth, I'd prefer having a primitive for the snapping whole.
Willy Tschager [Holly-Wood]
made the following comment.
2025-07-24 09:26:35
* I'm fine with the symmetrical 65084s01 and would just sub the common geometry in "yet" another sub. But your choice.
Added help lines for secondary hinge position. Kept origin as concluded in forum thread https://forums.ldraw.org/thread-28836.html