Unofficial File parts/70943p01.dat
Part Attributes:
Base Part: 70943.dat
File Header:
0 Figure Leg Mecha 2 x 4 x 6.333 Left with Black Friction Pin Pattern
0 Name: 70943p01.dat
0 Author: Gerald Lasser [GeraldLasser]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Licensed under CC BY 4.0 : see CAreadme.txt
0 BFC CERTIFY CCW
0 !KEYWORDS Bricklink 70943, Brickowl 8618, Brickset 70943, Rebrickable 70943c01
0 !KEYWORDS Set 71804, Set 75332
Show contents
1 16 0 0 0 1 0 0 0 1 0 0 0 1 s\70943s01.dat
1 16 40 -50 10 0 -1 0 1 0 0 0 0 1 studa.dat
1 16 40 -70 10 0 -1 0 1 0 0 0 0 1 studa.dat
1 16 40 -70 30 0 -1 0 1 0 0 0 0 1 studa.dat
1 16 40 -50 30 0 -1 0 1 0 0 0 0 1 studa.dat
1 16 32 -130 -10 0 -1 0 1 0 0 0 0 1 stud2a.dat
1 16 32 -110 -10 0 -1 0 1 0 0 0 0 1 stud2.dat
1 16 32 -130 10 0 -1 0 1 0 0 0 0 1 stud2a.dat
1 16 32 -110 10 0 -1 0 1 0 0 0 0 1 stud2a.dat
1 0 0 -118 0 0 0 1 0 1 0 -1 0 0 s\70943s02.dat
Status:
Needs 2 More Votes (N)
This part has the following automated holds from the Parts Tracker
Current Votes:
None
Official parents and subparts
Part Events:
Gerald Lasser [GeraldLasser]
initially submitted the part.
2026-03-06 19:14:47
Gerald Lasser [GeraldLasser]
submitted a new version of the part (all votes reset).
2026-03-06 19:17:00
Jeff Jones [notmaster]
made the following comment.
2026-03-07 09:00:07
Should be shortcut
Magnus Forsberg [MagFors]
made the following comment.
2026-03-07 09:26:41
This is a dual mould, right?
It's not possible to remove the pin. Then the file structure is good.
It's not possible to remove the pin. Then the file structure is good.
Jeff Jones [notmaster]
made the following comment.
2026-03-07 09:36:16
I saw that pin show up plenty of times
Also wonder if you could do that rancor using that model (or just the hands) which also needs a new part for the arm socket which showed up in galidor
Also wonder if you could do that rancor using that model (or just the hands) which also needs a new part for the arm socket which showed up in galidor
Rene Rechthaler [Blechtaler]
made the following comment.
2026-03-07 14:26:04
its strange that only one of the hollow top studs has the stud logo
(should be either all or none)
(should be either all or none)
Gerald Lasser [GeraldLasser]
made the following comment.
2026-03-07 16:05:48
stud2a does not induce a logo
Gerald Lasser [GeraldLasser]
made the following comment.
2026-03-07 16:06:59
@magnus, I really don'T know if the pins is liserted or molded in. I have only two of them and I don't want to destroy them...
Rene Rechthaler [Blechtaler]
made the following comment.
2026-03-07 16:08:39
yes but the one stud 2 has one, the 3 stud2a not -> 4x stud2a and more edge prims?
Creative Commons Attribution License information
This part is copyright ©
Gerald Lasser
Licensed under
CC BY 4.0